Analisis Penerapan Total Productive Maintenance (TPM) Menggunakan Overall Equipment Efectiveness (OEE) Dan Six Big Losses Pada Mesin Cold Leveller PT. KPS

Muhamad Bob Anthony(1*),

(1) Program Studi Teknik Industri, Fakultas Teknik, Universitas Serang Raya
(*) Corresponding Author


PT. KPS is one steel company in Indonesia that produces steel products in the form of slab and plate that is marketed in the country up to foreign countries. Cold leveller machine is a machine that serves to flatten the surface of the plate. Problems occurred in the machinery that is often experienced a breakdown so that the plate with uneven surfaces more and more because of the time machine working on the wane. This research aims to quantify the value of the overall equipment effectiveness (OEE), calculating the factor of six big losses and figure out the root cause of the problem, the dominant factor of the six big losses with the fishbone diagram. The OEE value obtained on the engine cold leveller is 82%. The biggest factor that causes the low effectiveness of the machine that is the reduced speed losses amounting to 11.59% and equipment failure losses amounted to 6.04%. The proposed corrective actions is prioritizing the main TPM pillar 3 that is autonomous maintenance, quality maintenance, training and education.

Keyword : fishbone diagram, overall equipment effectiveness (OEE), pareto, the six big losses, total productive maintenance (TPM)

PT. KPS adalah salah satu perusahaan baja di Indonesia yang memproduksi produk baja berupa slab dan plate yang dipasarkan di dalam negeri hingga ke luar negeri. Mesin cold leveller merupakan mesin yang berfungsi meratakan permukaan plate yang tidak rata. Permasalahan yang terjadi pada mesin tersebut yaitu sering mengalami breakdown sehingga plate dengan permukaan yang tidak rata semakin banyak karena waktu bekerja mesin semakin berkurang. Penelitian ini bertujuan untuk menghitung nilai overall equipment effectiveness (OEE), menghitung nilai faktor six big losses dan mengetahui akar penyebab masalah yang dominan dari faktor six big losses dengan fishbone diagram. Nilai OEE yang didapat pada mesin cold leveller adalah sebesar 82%. Faktor terbesar yang menyebabkan rendahnya efektifitas mesin yaitu reduced speed losses sebesar 11,59% dan equipment failure losses sebesar 6,04%. Tindakan perbaikan yang diusulkan adalah memprioritaskan 3 pilar utama TPM yaitu autonomous maintenance, quality maintenance, training dan education.

Kata Kunci: fishbone diagram, overall equipment effectiveness (OEE), pareto, six big losses , total productive maintenance (TPM)

Full Text:



O. V. Gaspersz and R. Qms-a, “Total Productive Maintenance ( TPM ): Bukan Sekedar Perbaikan Mesin.”

D. I. Rinawati and N. C. Dewi, “Analisis Penerapan Total Productive Maintenance (TPM) Menggunakan Overall Equipment Efectiveness (OEE) Dan Six Big Losses Pada Mesin Cavitec Di PT. Essentra Surabaya,” Progr. Stud. Tek. Ind. Fak. Tek. Univ. Diponegoro, vol. Prosiding, pp. 21–26, 2014.

U. Nurfaizah, H. Adianto, and H. Prassetiyo, “Rancangan Penerapan Total Productive Maintenance (TPM) Di Bagian Press II PT. XYZ,” Reka Integr., vol. 2, no. 1, 2014.

B. Kho, “Eight Pilar Total Productive Maintenance,”, 2019. [Online]. Available: [Accessed: 13-Jul-2019].

E. Y. T. Adesta, H. A. Prabowo, and D. Agusman, “Evaluating 8 pillars of Total Productive Maintenance ({TPM}) implementation and their contribution to manufacturing performance,” {IOP} Conf. Ser. Mater. Sci. Eng., vol. 290, p. 12024, Jan. 2018.

E. Yulian Triblas Adesta and H. Agung Prabowo, “Total Productive Maintenance (TPM) Implementation Based on Lean Manufacturing Tools in Indonesian Manufacturing Industries,” Int. J. Eng. Technol., vol. 7, no. 3.7, p. 156, 2018.

P. Amrih, “Overall Equipment Effectiveness,”, 1997. [Online]. Available: [Accessed: 13-Jul-2019].

D. Wahjudi, S. Tjitro, R. Soeyono, J. Siwalankerto, and S. Indonesia, “Studi Kasus Peningkatan Overall Equipment Effectiveness ( Oee ),” Univ. Stuttgart, 2009.

M. M. Firmansyah, A. Susanty, and D. Puspitasari, “Analisis Overall Equipment Effectiveness dan Six Big Losses pada Mesin Pencelupan Benang (Studi Kasus PT. Pismatex Textile Industry),” Ind. Eng. Online J., vol. 4, no. 4, 2015.

A. Maksum, “Pengumpulan data,” J. Metod. pengumpulan data, 2012.

Ali Maksum, “Data, Teknik Pengumpulan Data dan Instrumen Penelitian,” J. Cakrawala Kependidikan, no. agustus, p. 107, 2012.

D. H. Stamatis, The OEE primer: Understanding overall equipment effectiveness, reliability, and maintainability. 2017.

Carlo Scodanibbio, Overall Equipment Effectiveness (OEE), no. January. Italia:, 2009.

S. Nakajima, Introduction to TPM: Total Productive Maintenance (Preventative Maintenance Series) By Seiichi Nakajima. Japanese, 2019.

D. Agung, F. Debora, and H. H. Purba, “Increased Productivity of Injection Molding with Analysis of Overall Equipment Effectiveness ( OEE ),” Int. J. Res. Eng. Sci. Manag., vol. 1, no. 12, pp. 1–7, 2018.

A. Y. Tobe, D. Widhiyanuriyawan, and L. Yuliati, “The Integration of Overall Equipment Effectiveness (Oee) Method and Lean Manufacturing Concept To Improve Production Performance (Case Study: Fertilizer Producer),” J. Eng. Manag. Ind. Syst., vol. 5, no. 2, pp. 102–108, 2018.

D. Alvira, Y. Helianty, and H. Prassetiyo, “Usulan Peningkatan Overall Equipment Effectiveness OEE) Pada Mesin Tapping Manual Dengan Meminimumkan Six Big Losses,” J. Itenas Bandung, vol. 03, no. 03, pp. 240–251, 2015.

I. Nursanti and Y. Susanto, “Analisis Perhitungan Overall Equipment Effectiveness (Oee) Pada Mesin Packing Untuk Meningkatkan Nilai Availability Mesin,” J. Ilm. Tek. Ind., vol. 13, no. 1, pp. 96–102, 2014.


X. Blasco, J. M. Herrero, J. Sanchis, and M. Martínez, “A new graphical visualization of n-dimensional Pareto front for decision-making in multiobjective optimization,” Inf. Sci. (Ny)., vol. 178, no. 20, pp. 3908–3924, Oct. 2008.

S. Indonesia, “Analisis Akar Masalah dengan Fishbone Diagram,” 1, 2016. [Online]. Available:

R. Hutagaol, “Analysis of the Implementation of Nursing Professional Values in Referral Hospitals Jakarta: Fishbone Analysis,” Int. J. Nurs. Heal. Serv., vol. 2, no. 1, pp. 108–116, 2019.

H. P. Bloch, “Root Cause Failure Analysis,” in Petrochemical Machinery Insights, 2017.

Sitesgoogle, “Kelola Kualitas,”, 2016. [Online]. Available:

E. Zio and R. Bazzo, “Level Diagrams analysis of Pareto Front for multiobjective system redundancy allocation,” Reliab. Eng. Syst. Saf., vol. 96, no. 5, pp. 569–580, May 2011.

S. Wahyudi, “Penerapan Overall Equipment Effectiveness ( Oee ) Dalam Implementasi Total Productive Maintenance ( TPM ) ( Studi Kasus di Pabrik Gula PT . ‘ Y ’ .),” vol. 3, no. 3, pp. 431–437, 2012.

E. Y. T. Adesta, H. A. Prabowo, and D. Agusman, “Evaluating 8 pillars of Total Productive Maintenance (TPM) implementation and their contribution to manufacturing performance,” IOP Conf. Ser. Mater. Sci. Eng., vol. 290, no. 1, pp. 0–8, 2018.

“Introduction and certification of a quality assurance system : Helmut Ensslin. Quality Europe. Industrial Quality Assurance. 34th EOQ Annual Conference, Dublin, Ireland, 13 (1990),” Microelectron. Reliab., vol. 32, no. 1–2, p. 291, Jan. 1992.


Article Metrics

Abstract view : 602 times
PDF - 204 times


  • There are currently no refbacks.


Flag Counter