Analisa Risiko Keselamatan Dan Kesehatan Kerja Menggunakan Metode HAZOPs Di Area Gas Cleaning System Di PT. RK

Authors

  • Muhamad Bob Anthony Program Studi Teknik Industri, Fakultas Teknik, Universitas Serang Raya.

DOI:

https://doi.org/10.30737/jatiunik.v3i1.493

Keywords:

Gas Cleaning System, HAZOPs, Potential Of Hazard, Risk Levels

Abstract

PT. RK is one of the major international steel producing companies. This study aims to determine the potential hazards and the value of the level of risk that is likely to occur in the new plant owned by PT. RK i.e. the gas cleaning system area which is currently in the process of entering 95% progress. This study uses the Hazard & Operability Study (HAZOPs) method in analyzing risks in the gas cleaning system area of PT. RK. The Hazard & Operability Study (HAZOPs) method was used in this study because this method is very suitable for a new plant to be used. Based on the identification of potential hazards and risk analysis that has been done in the area of gas cleaning system using the HAZOPs method, it was found that 11 deviations that might occur from all existing nodes, i.e. for extreme risk levels of 1 (one) deviation or 9%, level high risk of 2 (two) deviations or 18%, moderate risk level of 6 (six) deviations or 55% and low risk level of 2 (two) deviations or 18%.

 

PT. RK merupakan salah satu perusahaan manufaktur besar penghasil baja berskala internasional. Penelitian ini bertujuan untuk mengetahui potensi bahaya dan nilai level risiko yang kemungkinan terjadi di plant baru milik PT. RK yaitu area gas cleaning system yang saat ini proses pekerjaannya sudah memasuki progress 95%. Penelitian ini menggunakan metode Hazard & Operability Study (HAZOPs) dalam menganalisa risiko di area gas cleaning system  PT. RK.  Metode Hazard & Operability Study (HAZOPs) digunakan dalam penelitian ini dikarenakan metode ini sangat cocok untuk sebuah plant baru yang akan digunakan. Berdasarkan identifikasi potensi bahaya dan analisa risiko yang telah dilakukan di area gas cleaning system dengan menggunakan metode HAZOPs, didapatkan bahwa 11 penyimpangan yang kemungkinan terjadi dari semua node yang ada yaitu untuk level risiko extreme sebanyak 1 (satu) penyimpangan atau sebesar 9%, level risiko high risk sebanyak 2 (dua) penyimpangan atau sebesar 18%, level risiko moderate sebanyak 6 (enam) penyimpangan atau sebesar 55% dan level risiko low risk sebanyak 2 (dua) penyimpangan atau sebesar 18%.

 

References

S. Ramli, Pedoman Praktis Manajemen Risiko dalam Perspektif K3 OHS Risk Management. Jakarta: Dian Rakyat, 2010.

E. Acar et al., “Development of Stitched, Braided and Woven Composite Structures in the ACT Program and at Langley Research Center (1985 to 1997),†J. Aircr., 2011.

J. Min, Y. Kim, S. Lee, T.-W. Jang, I. Kim, and J. Song, “The Fourth Industrial Revolution and Its Impact on Occupational Health and Safety, Worker’s Compensation and Labor Conditions,†Saf. Health Work, Sep. 2019.

A. Musyafa and H. Adiyagsa, “Hazard and Operability study in Boiler System of The Steam Power Plant,†Int. J. Sci. Technol. (IJSTE), vol. 1, no. 3, pp. 1–10, 2012.

K. Amponsah-Tawiah and J. Mensah, “Occupational Health and Safety and Organizational Commitment: Evidence from the Ghanaian Mining Industry,†Saf. Health Work, vol. 7, no. 3, pp. 225–230, 2016.

N. Hoboubi, A. Choobineh, F. Kamari Ghanavati, S. Keshavarzi, and A. Akbar Hosseini, “The Impact of Job Stress and Job Satisfaction on Workforce Productivity in an Iranian Petrochemical Industry,†Saf. Health Work, vol. 8, no. 1, pp. 67–71, 2017.

D. E. Gregory and S. E. Romero, “Can the use of an alternatively designed tamper alter spine posture and risk of upper limb injury while tamping espresso?,†Int. J. Ind. Ergon., vol. 65, pp. 103–109, 2018.

V. Golchha, P. Sharma, J. Wadhwa, D. Yadav, and R. Paul, “Ergonomic risk factors and their association with musculoskeletal disorders among Indian dentist: A preliminary study using Rapid Upper Limb Assessment,†Indian J. Dent. Res., 2015.

E. Jamilah, Y. H. Yadi, and A. Umyati, “Identifikasi Potensi Bahaya Dengan Metode Hazard And Operability Study ( HAZOP ) Di Area Boiler PT . XYZ,†J. Tek. Ind. Univ. Ageng Tirtayas, 2013.

N. Eizenberg, S., Shacham, M., Brauner, “Combining HAZOP with dynamic simulation Applications for safety education. Journal of Loss Prevention in the Process Industries,†J. Loss Prev. Process Ind., vol. 9, pp. 754–761, 2006.

C. A. Ericson, “Hazard Analysis Techniques for System Safety.†p. 1, 2015.

F. C. B. Tyler, HAZOP: Guide to Best Practic, 3rd ed. Elsevier, 2015.

L. Allford and R. Gowland, “Foreword,†HAZOP Guid. to Best Pract., pp. ix–xi, 2015.

C. Atombo, C. Wu, E. O. Tettehfio, G. Y. Nyamuame, and A. A. Agbo, “Safety and Health Perceptions in Work-related Transport Activities in Ghanaian Industries,†Saf. Health Work, vol. 8, no. 2, pp. 175–182, 2017.

AustralianStandard, “Australian Standard / New Zaeland Standard Risk Management 4360:2004.†Sydney and Wellington, New Zealand, p. 1, 2004.

et al. Cagno, E., F. Caron, Risk analysis in plant commissioning: the Multilevel Hazop." Reliability Engineering & System Safety. 2002.

et al Dunjó, J., V. Fthenakis, “Hazard and Operability (HAZOP) Analysis.†p. 1, 2010.

G. H. Choi, “Effectiveness of Direct Safety Regulations on Manufacturers and Users of Industrial Machines: Its Implications on Industrial Safety Policies in Republic of Korea,†Saf. Health Work, vol. 8, no. 1, pp. 59–66, 2017.

S. O. D. Ningsih and S. W. Hati, “Analisis Resiko Keselamatan Dan Kesehatan Kerja (K3) Dengan Menggunakan Metode Hazard And Operability Study (HAZOP) Pada Bagian Hydrotest Manual Di PT. Cladtek Bi Metal Manufacturing,†J. Appl. Bus. Adm., vol. 3 No.1, pp. 29–39, 2019.

W. Agus, “Analisis Kesehatan dan Keselamatan Kerja Dengan Metode Hazard And Operability (Hazop) Di Bengkel Dan Laboratorium Teknik Instalasi Tenaga Listrik SMK N 2 Wonosari 2017,†Pendidik. Tek. Elektro Fak. Tek. Univ. Negeri Yogyakarta 2017, 2017.

S. Rahayuningsih and J. A. Pradana, “Identifikasi Penerapan Dan Pemahaman Kesehatan Dan Keselamatan Kerja Dengan Metode Hazard And Operability Study (Hazop) Pada UMKM Eka Jaya,†JATI UNIK J. Ilm. Tek. dan Manaj. Ind., vol. 2, no. 1, p. 20, 2019.

Baradit Georgy, “A New Software-Based HAZOP Study Development Metodelogy.†Departement of Process Enginering, University of Pannonia, Hungaria, p. 1, 2007.

D. Retnowati, “Analisa Risiko K3 Dengan Pendekatan Hazard and Operability Study (Hazop),†Tek. Eng. Sains J., vol. 1, no. 1, pp. 41–46, 2017.

O. E. Williamson et al., “CAPACIDADES DINÂMICAS COMO DIFERENCIAL ESTRATÉGICO PARA A SUSTENTABILIDADE,†J. Bus. Res., 2016.

P. Paiton, P. T. Ytl, L. Kristianingsih, and A. S. Proses, “Analisis Safety System dan Manajemen Risiko pada Steam Boiler PLTU di Unit 5,†J. Tek. POMITS, 2013.

B. Pierre, J. Mathieu, G. Alexandre, and N. Anne-Sophie, “Fatigue-related risk perception among emergency physicians working extended shifts,†Appl. Ergon., vol. 82, no. November 2018, p. 102914, 2020.

D. Macdonald, Practical Hazops, Trips and Alarms, 1st ed. Newnes, 2004.

L. N. Wati, “Manajemen Risiko Bisnis,†Ekon. Bisnis dan Manaj., vol. I, no. September, pp. 255–267, 2012.

A. Wijaya, T. W. Panjaitan, and H. C. Palit, “Healty and Safety Management System,†1998. [Online]. Available: http://publication.petra.ac.id/index.php/teknik-industri/article/view/2979.

E. Mas’idah, W. Fatmawati, and L. Ajibta, “Analisa Manual Material Handling (MMH) dengan Menggunakan Metode Biomekanika Untuk Mengidentifikasi Resiko Cidera Tulang Belakang (Musculoskeletal Disorder),†Univ. Sultan Agung, vol. 45, no. 119, pp. 37–56, 2009.

P. Baybutt, “A critique of the Hazard and Operability (HAZOP) study,†J. Loss Prev. Process Ind., 2015.

Downloads

PlumX Metrics

Published

2019-10-30

How to Cite

Anthony, M. B. (2019). Analisa Risiko Keselamatan Dan Kesehatan Kerja Menggunakan Metode HAZOPs Di Area Gas Cleaning System Di PT. RK. JATI UNIK : Jurnal Ilmiah Teknik Dan Manajemen Industri, 3(1), 1–12. https://doi.org/10.30737/jatiunik.v3i1.493

Issue

Vol. 3 No. 1 (2019): October

Section

Articles

License

Information regarding Copyright and Licensing at JATI UNIK as follows:

  1. Licensed Use of Non - Commercial Articles will be governed by the Creative Commons Attribution license, which is featured on the Creative Commons Attribution Non-Commercial Share A Like 4.0 International License.
  2. The author guarantees that the articles published through JATI UNIK are original and do not contain statements that violate the law do not violate others' rights are subject to copyright, which is held exclusively by the author and free from the rights of third parties. The author is allowed to quote from various sources used for research and not to harm any party.
  3. JATI UNIK disseminates articles published with the rules set by Creative Commons. UNIK JATI license allows users to copy, distribute, display, and work for non-commercial purposes. Users also need to connect authors and JATI UNIK with the distribution of articles in journals.
  4. The Author rights, namely copyrights, ownership rights, patents, rights to use the substance of articles in the future, rights to reproduce articles for personal purposes and not to be traded, rights to conduct personal archives, rights to contract used for the non-exclusive distribution of articles published in the form a book and acknowledge the initial publication of the article originating from JATI UNIK.
  5. Suppose articles published by the author through JATI UNIK are compiled with other authors. In that case, it is necessary to create a form containing the authority of all authors involved in the article's production by including the agreement agreed upon by all authors in the article.
  6. The next point is, the agreement can be terminated if the author or JATI UNIK violates the agreement and cannot make repairs to the customer within a maximum of 2 months after being given information asking for the violation to be corrected. If there is no violation of the agreement, the license will automatically terminate and affect UNIQUE JATI UNIK.
  7. Regarding royalties, so far, if it is following applicable legal regulations, the author will waive his right to collect royalties on articles that have been licensed by JATI UNIK.
  8. In publishing the article, the editorial process is successful. JATI UNIK will continue it. JATI UNIK has the right to adjust articles related to punctuation, spelling, capital letters, references used, and usage adapted to JATI UNIK. The author acknowledges that the article can be published and accessed free of charge by the public.