Efektivitas Metode Pekerjaan Pelat Lantai Bondek, Half Precast dan Konvensional Gedung Asrama Putra Al-Azhar
DOI:
https://doi.org/10.30737/jurmateks.v6i2.4949Keywords:
Bondek, Cost, Floor Slabs, Half Precast, TimeAbstract
The floor plate is one of the important components in a multi-story building. Conventional methods are still widely used for building floor slabs. This method requires a lot of labor and time, which can reduce productivity. Other methods, such as bondek and half precast in floor slab work, are expected to increase work effectiveness and efficiency. This study aims to determine which method is most effective in floor slab work by reviewing cost, time, and work productivity. Floor plate planning consists of calculating each method's structural strength and volume of work, including formwork, reinforcement, concrete, and formwork dismantling. Cost analysis is carried out by collecting data on material prices and labor wages for the building's Draft Budget (RAB). Estimated work time involves formwork preparation, installation of reinforcement, and concrete casting for the three work methods. Based on the results of the calculation analysis on the floor slab work of the Al-Azhar Boys Dormitory Building with an area of the floor plate of 375,318 m2. Conventional floor slab work is more economical than bondek slab work by around 31.23%, but requires the longest work time. Meanwhile bondek floor slabs offer the fastest processing time, even though the cost is higher than conventional slabs, around 31.19% and 5.18% lower than half precast slabs. This can be a recommendation in choosing a floor slab work method.
References
I. G. Pamungkas, F. N. Abdi, and M. Jamal, “Analisis Perbandingan Metode Pelaksanaan Halfslab dengan Cast in Situ dan Floordeck Terhadap Biaya dan Waktu Pada Pelat Lantai Proyek Pembangunan Apartemen,” J. Sipil Sains, vol. 09, no. 1, pp. 9–16, 2018.
H. Girsang and I. Khalid, “Comparative Analysis of Conventional and plates Floor Plate Floor Area Bondek PIM 3 Basement Project and Cost Performance Againts Time,” Neutron, vol. 20, no. 01, pp. 48–55, Jul. 2020, doi: 10.29138/neutron.v20i01.48.
K. Cho, Y. su Shin, and T. Kim, “Effects of half-precast concrete slab system on construction productivity,” Sustain., vol. 9, no. 7, 2017, doi: 10.3390/su9071268.
Paryanto and L. Hendarti, “Analisis Perbandingan Biaya Pelaksanaan Pelat Beton Dengan Metode Bondex Dan Konvensional,” pp. 25–32, 2021.
I. G. A. Diputera and K. Kurniari, “Analisis Perbandingan Biaya Pekerjaan Pelat Lantai Menggunakan Pelat Konvensional dan Pelat Bondek pada Proyek Apartemen Taman Sari,” Fak. Tek. UNR, pp. 40–49, 2020.
I. G. S. Wibawa, I. P. R. S. Wiguna, I. made Tapayasa, and I. M. A. Santiana, “Perbandingan Kebutuhan Biaya Pekerjaan Pengecoran Pelat Lantai Metode Konvensional Dengan MetodeFloor Deck Studi Kasus Pada Pembangunan Proyek the Hattens Wines Bali,” J. Log., vol. 17, no. 1, pp. 60–68, 2019.
A. Gemilang and B. Herumanta, “Perbandingan Rencana Anggaran Biaya Pelat Konvensional Dengan Pelat Bondek Pada Proyek Pembangunan Gedung Apartemen Dhika Universe, Yogyakarta,” 2019.
Trijeti, F. D. Atmawan, and M. Aswanto, “Time and cost comparison of conventional and alternative plate hollow slab, Halfslab and Metaldeck,” Int. J. Sci. Technol. Res., vol. 7, no. 6, pp. 61–66, 2018.
O. Wijaksono, J. Tistogondo, and T. H. Bagio, “Analisis Perbandingan Efisiensi Waktu Dan Biaya Antara Metode Konvensional Slab , Precast Half Slab Dan Precast Full Slab Pada Proyek Bangunan Hotel Bertingkat Di Surabaya,” in Seminar Nasional Sains dan Teknologi, 2018, pp. 1–9.
B. R. K. Holla, S. Anant, M. A. Mohammad, A. Periwal, and A. Kapoor, “Time, Cost , Productivity and Quality Analysis of Precast Concrete System,” Int. J. Innov. Sci. Eng. Technol., vol. 3, no. 5, pp. 252–257, 2016.
M. N. Fadlany and F. Nugraheni, “Analisis Perbandingan Biaya Antara Pelat Konvensional Dengan Pelat Bondek Pada Proyek Pembangunan Pasar Prambanan,” no. 28, pp. 1–9, 2019.
U. Suaiba, D. Sarasanty, and W. A. Asrining, “Analisa Perbandingan Sistem Half Slab Dan Plat Konvensional Ditinjau Dari Segi Waktu Dan Biaya Pada Proyek Apartemen Gunawangsa Tidar Surabaya,” Tek. Sipil, vol. 1, no. 1, pp. 1–9, 2019.
R. Rahman, “Analisis Perbandingan Biaya Pelat Lantai Antara Metode Precast Half Slab dan Metode Konvensional,” 2019. doi: 10.31227/osf.io/n4f68.
D. Aprisandi, “Analisis Biaya Dan Waktu Metode Half Slab Dalam Pembangunan Proyek Konstruksi,” JURNALIS J. Lingkung. Dan Sipil, vol. 1, no. 1, pp. 51–61, 2018.
A. Asroni, Balok dan Pelat Beton Bertulang. Yogyakarta: Graha Ilmu, 2010.
American National Standards Institute/Steel Deck Institute, ANSI/SDI C-2017 Standard for Composite Steel Floor Deck-Slabs. 2017.
SNI-07-0663, “Jaringan Kawat Baja Las untuk Tulangan Beton,” 1995.
R. Hidayah, A. Ridwan, and Y. Cahyo, “Analisa Perbandingan Manajemen Waktu Antara Perencanaan Dan Pelaksanaan (Studi Kasus: Pada Gedung Asrama Pondok Pesantren Sananul Huda Di Selorejo Kab. Blitar),” J. Manaj. Teknol. Tek. Sipil, vol. 1, no. 2, pp. 281–290, 2018, doi: 10.30737/jurmateks.v1i2.416.
L. Mulyadi and L. K. Wulandari, “Cost Comparison of Conventional Floor Slab and Steel Deck Slabs,” Int. Res. J. Adv. Eng. Sci., vol. 7, no. 3, pp. 187–190, 2022.
E. Adityo, D. Katni, and A. Nursandah, “Kajian Metode Struktur Pelat Konvensional terhadap Pelat Pracetak Segmental dan Pelat Bondek Ditinjau dari Segi Waktu, Biaya dan Struktur,” Agregat, vol. 5, no. 1, pp. 387–395, 2020, doi: 10.30651/ag.v5i1.4977.
N. C. Fertilia and M. F. D. Sukmana, “Comparison Analysis of Conventional Method Floor Slabs With Half Slab Method Against Cost and Time of XYZ Project,” J. World Conf., vol. 3, no. 2, pp. 234–240, 2021.
R. Nugrahawan, “Perbandingan Biaya Dan Waktu Pekerjaan Pelat Lantai Beton Antara Sistem Bondek Dan Sistem Konvensional Secara Teoritis Dan Praktis (Comparison of Cost and Time of Concrete Floor Slab Work Between Floor Deck and Conventional System Theoretically and Practi,” 2021.
I. Riyadi, E. Handayani, and W. Dony, “Analisa Perbandingan Sistem Pelat Konvensional dengan Sistem Precast Half Slab dalam Segi Waktu dan Biaya,” J. Civronlit Unbari, vol. 7, no. 2, p. 63, 2022, doi: 10.33087/civronlit.v7i2.100.
D. H. Wisanggeni, “Perbandingan Sistem Pelat Konvensional Dan Precast Half Slab Ditinjau Dari Segi Waktu Dan Biaya Pada Proyek My Tower Apartement Surabaya,” 2017.
Downloads
Published
Issue
Section
License
Copyright (c) 2023 Muhammad Romadhoni, Muh. Nur Sahid
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Authors who publish with this journal agree to the following terms:
(1) The copyright of published articles will be transferred to the journal as the publisher of the manuscript. Therefore, the author needs to confirm that the copyright has been managed by the publisher with the Publication Right Form which must be attached when submitting the article.
(2) Publisher of JURMATEKS is Kadiri University.
(3) The copyright follows Creative Commons Attribution-ShareAlike License (CC BY SA): This license allows to Share copy and redistribute the material in any medium or format, Adapt remix, transform, and build upon the material, for any purpose, even commercially.
